Motion Pro Micro Fork Bleeder

Next to worthless on WP because they are always getting broken from sitting too high and unprotected over the fork cap. Great on KYB etc that offers some side wall protection

A must-have! Great Value and performance over 1.5 years

-m-2016 HONDA CRF450X--

fits well, just follow directions with package. the only thing bad about these is the screwdriver slot is very wide . i had to get a extra thick driver .

-m-2010 YAMAHA WR250R--

Awesome product, easy to install and works great.its a must if you plan on moving your handle bars forward.

Good buy. Much easier use then the stock screws that come on bike

Super easy to put on and its something that could save you time and money as long as you bleed the air regularly. I use it when I'm changing elevations or even just trying the bike down. Bikes really should come stock with these

-m-2015 KTM 250 SX--

didn't think I needed them, but with the aer air forks having an enclosed air chamber the outer chamber still pumped up with air. these bleeders makes it easy to check them.

-m-2018 HUSQVARNA FC 450--

This does not fit the fork, there is interference between the preload adjuster and it, does not fit without modification.

-m-2018 HUSQVARNA FE 350--

the fastest and easiest way to relieve any pressure you may have. Just push these buttons and go.

-m-2005 YAMAHA YZ250F--

They work as advertised and save so much time, worth every penny.

-m-2004 YAMAHA YZ125--

It works, but there are others that will tighten up better than a flat head screwdriver.

-m-2001 HONDA CR250R--

Easy to install & works great on your forks to release excess air psi.

The fork bleeders fit perfectly and saves me time bleeding the air out of my forks.

You basically have to scratch them to put on, wish there was a better way than using a flathead

These make for a great gadget. Only complaint is that on my bike they screw into the fork too far, apparently blocking the bleeder hole and not allowing air out unless I unscrew them about 1/4 turn. I put the o-rings from the original screws on with the ones that come with these valves and it seems to work now.

Fits good, looks good, perfect for a quick swap out that won’t break the bank.

The motion pro fork bleeders are a must have. They are priced nicely , durable and help your forks life. Anyone can install them in a matter of seconds with just a straight screw driver. I would definitely recommend these to anyone looking to help there forks last longer. Definitely must have

-m-2001 YAMAHA YZ426F--

In my opinion this id an item you must have, that way you bleed your forks without using tools. It prevents pressure in the forks. I have them on all my bikes.

-m-2004 KTM 200 EXC--

Just installed then which was real easy. So far I like the no tools needed to bleed the air out I can now do it sitting at the line

-m-2010 HONDA CRF450R--

2 Minute install... way easier than trying to find a screwdriver, worrying about dropping a screw..

-m-2009 KTM 250 XC-F--

stop getting a screwdriver out and fumbling with those little flat heads be cool and buy the buttons they're great for the price and work good, only complaint is they can be tricky to get in use the correct screw driver or risk scratching them

Yes, they are super easy to install. If you have a super huge flat head screwdriver, which I do not. I used a spatula and slipped two times, which was enough to totaly mess up the nice black ring you see around the blue button. I took them back off my forks again, because the o-ring would not seal properly and so far I have not put them back on.

If you use them, don't loose the original screws, as you have to put them back on when you're ever going to service your forks. Why? Because on my WP bladder style forks the service requires to put the fork heads down on the ground and the bleeders are sticking out. So you would put the whole weight on the little bleeders, which could end up breaking them.

-m-2008 KTM 250 XC-F--

Allows you to easily bleed off the pressure in the forks before a ride. Install is simple, you may need to rotate your forks a little in the triple clamps to gain access.

-m-2018 KTM 250 XC-W i (Fuel Injected)--

So far they've been great. It's nice not to need to fit a screwdriver in between the handlebars and then if the screw falls out trying to get it started again.

-m-2007 YAMAHA YZ250--

I was so satisfied with the these micr fork bleeders, that I bought them for all of my Bikes.

-m-2002 KAWASAKI KX250--

Ruined a day of riding. Just finished up a nice build on my CR250 and went on the first ride. Stupid thing shot right out of the forks 30mins in. I had these before but I will never buy them again. Waste of time and money.

-m-2003 HONDA CR250R--

Cant beat the price and they do what they are intended to do and can save your fork seals before strapping the bike down

these only lasted 2 rides before they were leaking all the time.

-m-2014 KTM 350 XCF-W--

I would more than recommend this weather your a seasoned rider or new to all of this. For a few dollars u don’t need any tools to bless the trapped air off from your front folks which in turn will cause
Your folks to respond better// how they should respond and that will give you a better//more comfortable ride... this is one of those common sense parts!!!

-m-2005 KAWASAKI KX250F--

They just work, easy to install and even easier to use. Great value.

-m-2011 KTM 250 SX-F--

So much easier to bleed the forks with these. Especially with wrap around handguards and all the other crap that's on the bars. Must have for the price.

-m-2018 KTM 350 XC-F--

Installation was super difficult, you literally had to unscrew a screw and than screw in the fork bleeder ??. A small investment and noticeable difference.

-m-2015 YAMAHA YZ450F--

Why wouldn't you want these instead of the stock flat blade screws? Perfect fit and easy to use with or without gloves. If your bar mounts are low and back you may have to rotate the forks a few degrees in the triple clamps to clear.

Works great easy install and easy to use. Yeah better then the stock set up.

-m-2017 KTM 350 XC-F--

THIS BLEEDER SURE MAKES GETTING THE AIR OUT OF YOUR FORK NICE AND EASY. BEATS TAKING THE SCREW OUT EVERY TIME YOU NEED TO BLEED THEM.

-m-2001 HONDA CR250R--

If your bleed screws were stripped like mine, then these are for you. Especially when parts become obsolete on an older bike and you cannot get parts like bleed screws anywhere. It was also nice to be able to bleed the forks while riding and remove some of the harshness from the front end. I will put these on my next bike for sure.

-m-2001 YAMAHA YZ250F--

So much easier than a screw driver. Buy them save time.

Highly recommended
Makes bleeding the forks a breeze
No more screwdrivers

-m-2016 KTM 250 XC-F--

They install quick and easy and work really good a lot better than having to unscrew them all the time

Great product!! Eliminates remembering a screwdriver everywhere.

-m-2017 YAMAHA YZ250F--

A must have for open chamber forks. I installed them on my wp xplor 48 forks on a 2017 KTM 350 EXC-F. They fit just fine which the description did not specify specifically. So much easier to bleed the forks than messing around with a screwdriver.

Proper fit and does the job!

-m-2017 KTM 350 XC-F--

Makes bleeding the air out of the forks much easier. No need to go to the tool box to complete such a simple task.

-m-2018 HUSQVARNA FC 350--

It looks great, it's affordable, easy to use, easy to install, and saves me a little time at the track. Great product!

-m-2018 HONDA CRF450R--

Easy install , simple function, great price .

-m-2018 HUSQVARNA TX 300--

Highly recommend as they are easy to bleed your forks and is a good quality product

Stock fork bleeder screws were hard to get to because the handlebars were in the way. These work great, just push the button.

-m-2008 HONDA CRF450R--

Prevent fork seal leakage with just a push of a button.

I will always use these on all my bikes . They make it convenient to keeping the forks functioning as they should.

They leak a little bit of fork oil, but they make bleeding the forks so much easier.