motorcycle Seats & Covers

You are viewing a combination of machine-specific and universal parts. Please choose a machine to display parts specific to your machine or select a part below.

Choose a machine

User Tip: If you're unsure of your vehicle type, you may skip the machine type selection box.

Use one of my Saved Machines

Motorcycle Seats

Your motorcycle seat could easily make or break every ride you ever go on. Make sure you have the right motorcycle seat for you by browsing through our selection to find the seat that best suits you and your motorcycle.

Latest Seats & Covers Reviews – You could win up to $500 for reviewing products!

  • Seat Concepts Complete Seat

    Seat Concepts Complete Seat

    JOHN in ON

    I just finished a 6k trip of the Labrador highway.

    I purchased the seat just for this ride ! It's a little expensive but the comfort was great. Durability was not been a issue with dragging my boots across the seat due to the height of the bike.

    Read All Reviews
  • Attack Graphics Factory Seat Cover

    Attack Graphics Factory Seat Cover

    Ken in CO

    There are better options available

    This is the second seat cover I've purchased. I bought this one because it was inexpensive, but it turns out it's just cheap. The material is not at all stretchy, so installation is both difficult and leaves wrinkles. The cover is cut really small, so there's barely enough there to wrap around to base for stapling. And the feel is REALLY rough on the backside. Good traction is one thing, but this stuff is like sitting on belt sander.

    Read All Reviews
  • Seat Concepts Seat Cover and Foam Kit With Pan Pocket

    Seat Concepts Seat Cover and Foam Kit With Pan Pocket

    Greg in UT

    Not a bad install and looks fine

    I bought this instead of the full seat because it was cheaper. After watching a few online videos, I figured I could install the cover. The installation went fine and the seat looks great. I haven't ridden on it much yet, so I can't comment on the comfort, but I'm sure it will be better than stock. If you choose this option, here are a few tips to make the install go smoothly: -Buy an air stapler. it makes the install much easier than using a manual stapler. -Spend the time to thoroughly clean the pan after removing the stock cover. It will allow for better adhesion of the new foam and prevent potential bulging. -Put the cover in the sun for awhile to soften it up. It stretches over the pad much easier. -When stretching the sides to staple them, work from side to side, ensuring that the cover is centered all the way down. I put a staple about every 4-5 inches at first just to get the cover in place, then went back and put more staples in between after the placement was set. -Dry fit the seat on the bike before adding more staples and trimming excess material in case you need to redo something. -Don't over-stretch the cover or it will compress the foam and reduce comfort. -Use stainless steel staples to prevent rusting over time. Overall, it looks like a good seat option. I'm going to be doing some long rides this summer, so I hope it helps the comfort level!

    Read All Reviews
  • Husqvarna Low Complete Seat

    Husqvarna Low Complete Seat

    Keith in NJ

    Hard seat; not sure if it is worth the price.

    Torn on this review. Not sure if the seat is worth the price. It is not that noticeably different from the stock seat. 1/2” if you are lucky. Seat is hard as a rock too. Looks good though and fitment was perfect.

    Read All Reviews
  • Tusk ATV/Motorcycle Seat Heater

    Tusk ATV/Motorcycle Seat Heater

    Gary in MT

    Seat warmer instal

    At this point I have the seat part installed but have not yet gotten to the wiring part, too much else going on. It seems a easy instal especially if you watch the video. I had to buy a pneumatic staple gun but have used it for other things..

    Read All Reviews
  • Seat Concepts Seat Cover and Foam Kit

    Seat Concepts Seat Cover and Foam Kit

    Glenn in AZ

    Nice upgrade

    As far as do it yourself projects go this one wasn’t too bad. Bear in mind, you will need a power stapler to make this job easier. Stapling through the plastic seat pan would be really hard with a hand stapler. Just follow the enclosed instructions and take your time and you shouldn’t have any issues. I went with the lower pad option and it’s plenty comfortable on my DRZ 400 S.

    Read All Reviews
RM Cash ProgramParts Finder